NZW30 Quick Setup for SmartThings Users

NZW30

Thank you for your purchase of the NZW30 Smart Switch. If you run into any problems along the way, please contact us. We’re here to help!

Step by Step Instructions – Android Users

(iOS Users, please click here or scroll down about halfway)

– Step 1 –
Gather Your Materials & Find an Appropriate Outlet

Materials Needed:

  • Gangbox (With Neutral, Line & Load Wires)
  • Cell Phone or Tablet
  • SmartThings HUB 1.0 or 2.0

Locate an area to install your switch within the recommended distance (calculated on Page 2-3 in your manual) from your HUB.

Walls, furniture, and other obstructions may affect the communication between the Plug-In Module and your Hub/Gateway, so please keep this in mind when selecting your location.

Follow the recommended wiring instructions located in Step 2.

**If you are having issues pairing your device, please ensure your switch is within range of your HUB. 95% of the pairing/including failures stem from this issue. Best practice is to start with Z-Wave products near your HUB and build your network out. The more Z-Wave devices, the more efficient your network.**

-Step 2-
Wiring Diagrams

Please follow the recommended wiring diagrams below. If your wiring diagram does not look like the below, please reach out and we will try our best to help (although we are not electricians).

Here are some Pro-Tips to follow:

  • Remember to turn off the power prior to installation and ensure all connections are made prior to turning the power back on
  • The Line wire is Hot. Please use a multimeter to find it.
  • Our smart switches will work with normal 3-Way Switches. You do not need a special Auxiliary Switch
  • Our switches require a Neutral wire. Please do not try wiring without one.
  • Please remember to Ground all connections
  • Remember to start the inclusion process prior to flipping the power back on
  • Use Wire-Strippers to cut 1″ for screw installation and 5/8″ for Terminal Installation

**If you are having issues pairing your device, please ensure your switch is within range of your HUB. 95% of the pairing/including failures stem from this issue. Best practice is to start with Z-Wave products near your HUB and build your network out. The more Z-Wave devices, the more efficient your network.**

-Step 3-
Adding (Including) to the Network & Completing the Setup Process

Please do not turn the power back on until you start the actual inclusion process — this switch has, “Auto-Inclusion” so if you switch the power on too early, it will not auto-include and you will have to do the backup method.

Now that your switch is installed, we’ll start the inclusion process.

Including Steps:

  • Open up your SmartThings app and click on the, “My Home” tab, followed by the, “Things” tab
  • Walk down to your circuit breaker and flip on the power (you will now have 30 seconds to press, “Add a Thing” in your SmartThings app)
  • While next to the breaker, press, “Add a Thing” (at the bottom) or the (+) at the top right to start adding the switch and SmartThings will automatically start looking for devices
  • Wait for auto-inclusion to do its thing. It will automatically include/pair to your HUB
    • If successful, your device will flash twice (NOTE: Auto-Inclusion will time out after 30 seconds)
    • If it does not flash within 30 seconds, please use the alternate method of pairing which is pressing the top button 6x within 2 seconds
  • You should now see that your device is detected (“Z-Wave Switch” should appear)

Setup After Inclusion

  • After your device was detected, press, “Save” (or if you’d like to rename your device, you can do that and then click, “Save”)
  • Once you click, “Save” a pop up will appear asking you to, “Confirm Paired Devices” — Click, “OK”
  • Now you are back at the, “My Home” screen and you will see the Z-Wave switch on the screen which is labeled, “Z-Wave Switch”

**If you are having issues pairing your device, please ensure your switch is within range of your HUB. 95% of the pairing/including failures stem from this issue. Best practice is to start with Z-Wave products near your HUB and build your network out. The more Z-Wave devices, the more efficient your network.**

-Step 4-
Run a Z-Wave Refresh to Update Your Mesh Network With Your New Switch (OPTIONAL: But Recommended)

This step is highly recommended whenever a new Z-Wave device is added to your network. It tells your HUB to re-map the network which, ultimately, will make your network faster and more efficient.

Z-Wave Refresh Steps:

  • In the SmartThings app, click on the, “Menu” button
  • Then click, “Hub is Online”
  • Next click, “Z-Wave Utilities”
  • Next click, “Repair Z-Wave Network”
  • Finally, click, “Start Z-Wave Network Repair”
  • Wait 20 minutes for your SmartThings HUB to re-map (discover) the network
    NOTE: Do not touch anything on your network during this time

Congratulations, you now have a smart switch!

-Device Removal-
Removing Your Smart Switch From SmartThings

Please follow the below directions to remove your smart switch from your SmartThings HUB.
(NOTE: this is the same process for SmartThings HUB’s 1.0 & 2.0)

Removal Steps:

  • From the, “My Home” screen (make sure you are on your, “Things” tab — located at the top) click on the device you’d like to remove
  • Click on the gear icon (top right of the screen)
  • Press the red, “Remove” button at the bottom
  • On the removal screen, you may receive a pop-up asking if you’re sure you want to remove this device
    • Press, “Remove Anyway”
  • Press the Top (UP) Button on your NZW30 six (6) times within 2 seconds
    • If successful, you will see a message saying that the device was successfully removed from SmartThings
    • If unsuccessful, you will see a message saying that the device failed to be removed from SmartThings — if this happens, please move the plug closer to the HUB and try again.

Your smart switch should now be removed from the SmartThings HUB.

Full Installation Videos

(Coming Soon)

Below you will find our full installation videos for the Smart Switch.  There are two videos that will be useful for when you set up your smart plug. The first video shows the entire pairing process, while the second video helps you set up a schedule with your smart plug (ie: if you want your plug to turn on and off at certain times). Thank you for your purchase and we hope you enjoy your product!

SmartThings "Light Schedule" Setup

Step by Step Instructions – iOS

(Android Users, please click here or scroll up to the top)

– Step 1 –
Gather Your Materials & Find an Appropriate Outlet

Materials Needed:

  • Gangbox (With Neutral, Line & Load Wires)
  • iPhone or iPad
  • SmartThings HUB 1.0 or 2.0

Locate an area to install your switch within the recommended distance (calculated on Page 2-3 in your manual) from your HUB.

Walls, furniture, and other obstructions may affect the communication between the Plug-In Module and your Hub/Gateway, so please keep this in mind when selecting your location.

Follow the recommended wiring instructions located in Step 2.

**If you are having issues pairing your device, please ensure your switch is within range of your HUB. 95% of the pairing/including failures stem from this issue. Best practice is to start with Z-Wave products near your HUB and build your network out. The more Z-Wave devices, the more efficient your network.**

-Step 2-
Wiring Diagrams

Please follow the recommended wiring diagrams below. If your wiring diagram does not look like the below, please reach out and we will try our best to help (although we are not electricians).

Here are some Pro-Tips to follow:

  • Remember to turn off the power prior to installation and ensure all connections are made prior to turning the power back on
  • The Line wire is Hot. Please use a multimeter to find it.
  • Our smart switches will work with normal 3-Way Switches. You do not need a special Auxiliary Switch
  • Our switches require a Neutral wire. Please do not try wiring without one.
  • Please remember to Ground all connections
  • Remember to start the inclusion process prior to flipping the power back on
  • Use Wire-Strippers to cut 1″ for screw installation and 5/8″ for Terminal Installation

**If you are having issues pairing your device, please ensure your switch is within range of your HUB. 95% of the pairing/including failures stem from this issue. Best practice is to start with Z-Wave products near your HUB and build your network out. The more Z-Wave devices, the more efficient your network.**

-Step 3-
Adding (Including) to the Network & Completing the Setup Process

Please do not turn the power back on until you start the actual inclusion process — this switch has, “Auto-Inclusion” so if you switch the power on too early, it will not auto-include and you will have to do the backup method.

Now that your switch is installed, we’ll start the inclusion process.

Including Steps:

  • Open up your SmartThings app and click on the, “My Home” tab, followed by the, “Things” tab
  • Walk down to your circuit breaker and flip on the power (you will now have 30 seconds to press, “Add a Thing” in your SmartThings app)
  • While next to the breaker, press, “Add a Thing” (at the bottom) or the (+) at the top right to start adding the switch and SmartThings will automatically start looking for devices
  • Wait for auto-inclusion to do its thing. It will automatically include/pair to your HUB
    • If successful, your device will flash twice (NOTE: Auto-Inclusion will time out after 30 seconds)
    • If it does not flash within 30 seconds, please use the alternate method of pairing which is pressing the top button 6x within 2 seconds
  • You should now see that your device is detected (“Z-Wave Switch” should appear)

Setup After Inclusion

  • After your device was detected, press, “Save” (or if you’d like to rename your device, you can do that and then click, “Save”)
  • Once you click, “Save” a pop up will appear asking you to, “Confirm Paired Devices” — Click, “OK”
  • Now you are back at the, “My Home” screen and you will see the Z-Wave switch on the screen which is labeled, “Z-Wave Switch”

**If you are having issues pairing your device, please ensure your switch is within range of your HUB. 95% of the pairing/including failures stem from this issue. Best practice is to start with Z-Wave products near your HUB and build your network out. The more Z-Wave devices, the more efficient your network.**

-Step 4-
Run a Z-Wave Refresh to Update Your Mesh Network With Your New Switch (OPTIONAL: But Recommended)

This step is highly recommended whenever a new Z-Wave device is added to your network. It tells your HUB to re-map the network which, ultimately, will make your network faster and more efficient.

Z-Wave Refresh Steps:

  • In the SmartThings app, click on the, “Menu” button
  • Then click, “Hub is Online”
  • Next click, “Z-Wave Utilities”
  • Next click, “Repair Z-Wave Network”
  • Finally, click, “Start Z-Wave Network Repair”
  • Wait 20 minutes for your SmartThings HUB to re-map (discover) the network
    NOTE: Do not touch anything on your network during this time

Congratulations, you now have a smart switch!

-Device Removal-
Removing Your Smart Switch From SmartThings

Please follow the below directions to remove your smart switch from your SmartThings HUB.
(NOTE: this is the same process for SmartThings HUB’s 1.0 & 2.0)

Removal Steps:

  • From the, “My Home” screen (make sure you are on your, “Things” tab — located at the top) click on the device you’d like to remove
  • Click on the gear icon (top right of the screen)
  • Press the red, “Remove” button at the bottom
  • On the removal screen, you may receive a pop-up asking if you’re sure you want to remove this device
    • Press, “Remove Anyway”
  • Press the Top (UP) Button on your NZW30 six (6) times within 2 seconds
    • If successful, you will see a message saying that the device was successfully removed from SmartThings
    • If unsuccessful, you will see a message saying that the device failed to be removed from SmartThings — if this happens, please move the plug closer to the HUB and try again.

Your smart switch should now be removed from the SmartThings HUB.

Full Installation Videos

(Coming Soon)

Below you will find our full installation videos for the Smart Switch.  There are two videos that will be useful for when you set up your smart plug. The first video shows the entire pairing process, while the second video helps you set up a schedule with your smart plug (ie: if you want your plug to turn on and off at certain times). Thank you for your purchase and we hope you enjoy your product!

SmartThings "Light Schedule" Setup