NZW39 Quick Setup for Vera
(Auto-Inclusion)

Z-Wave Plug - Zwave Plus with Scene Control (NZW36 - Inovelli)

Thank you for your purchase of the NZW39 (Auto-Inclusion Enabled) Smart Plug. If you run into any problems along the way, please contact us. We’re here to help!

Step by Step Instructions

– Step 1 –
Gather Your Materials

Materials Needed:

  • Grounded Outlet
  • Mac/PC
  • Vera HUB UI5 or UI7

Next, we’ll locate an indoor outlet which is grounded and within the recommended distance from your Z-Wave Hub/Gateway.

When you’re ready to select your plug’s location, please move onto, “Step 2”.

Walls, furniture, and other obstructions may affect the communication between the Plug-In Module and your Hub/Gateway, so please keep this in mind when selecting your location.

**If you are having issues pairing your device, please make sure you are within range above. If you are confident you are, please click on the, “Exclusion / Device Removal” tab below to exclude your device first**

-Step 2-
Select Your Location

Please use the below Z-Wave Worksheet to determine whether or not your location is suitable for your Z-Wave device.

Here’s how to use the Z-Wave Worksheet:

  • Go to where you want your switch to be located (or where it’s already located) and look straight towards your HUB (or nearest Z-Wave repeater)
  • Count how many walls, furniture, or other obstructions are in the way and write the down
  • Then use the chart and figures below to figure out if the switch should be within range

Z-Wave Worksheet (from your instructions)
Please use the below to calculate whether or not your switch is within range.
(NOTE: you can ignore the, “Page 2” below — this picture is taken from our instruction manual):

A Note on Max Wattage:

Please make sure to not exceed the max wattage for this device, which is 500W.

For best performance, use a CFL or Incandescent bulbs that are dimmable. If you’d like to use an LED bulb, please note that not all bulbs work properly with our device (as well as most dimmable switches and plugs in the market) and you may experience flickering or the bulb may not fully shut off.

Because we are personal advocates of LED bulbs, we’ve tested multiple bulbs and brands and have put together a list of bulbs that are compatible and work well with our module. Please see the, “Recommended LED Bulbs” tab below.

Note: It is not recommended plugging in space (electric) heaters, or any other appliances that may present a hazardous condition due to unattended, unintentional, or automatic power control.

**If you are having issues pairing your device, please make sure you are within range above. If you are confident you are, please click on the, “Exclusion / Device Removal” tab below to exclude your device first**

-Step 3-
Adding (Including) to the Network & Completing the Setup Process

Alright, let’s include your device!

Please do not plug in your device until you start the actual inclusion process — this plug has, “Auto-Inclusion” so if you plug it in too early, it will not auto-include.

Including Steps:

  • On the Main screen, click on the, “Devices” tab
  • Click, “Add Device”
  • Scroll down near the bottom and click, “Generic Z-Wave Device”
  • Under the, “Pair Your Device”, click “Next” until your HUB goes into inclusion mode
  • Plug in your device and let the device’s, “Auto-Inclusion” find the signal from the HUB.
    • If successful, your device will flash twice (NOTE: Auto-Inclusion will time out after 30 seconds)
    • If it does not flash within 30 seconds, please use the alternate method of pairing which is pressing the middle button 5x rapidly (within 1-2 seconds).
  • If successful, you will see a new screen pop up and there will be a notification that says, “Device Detected”
  • Go ahead and name your device
  • Select a Room and hit, “Finish”
  • Wait for the device to appear

Check to make sure your device turns on and off and if so, congratulations, you now have remote control over your lights!

STILL CAN’T GET IT TO PAIR? You may need to exclude the device first. While this is rare, sometimes it happens. Please click see the, “Exclusion / Device Removal” section below. Once that’s completed, please return here.

**If you are having issues pairing your device, please make sure you are within range above. If you are confident you are, please click on the, “Exclusion / Device Removal” tab below to exclude your device first**

-Device Exclusion / Removal-
Excluding or Removing Your Smart Plug From Vera

Please follow the below directions to remove your smart plug from your Vera HUB.


Exclusion Steps - Use if having issues Pairing

Removal Steps - Use only for Removing a Device

**If you are having issues removing your device, try removing the device directly next to the HUB. This will solve 95% of all problems you may have when removing**

Full Installation Videos

(Coming Soon)

Below you will find our full installation videos for the Smart Switch.  There are two videos that will be useful for when you set up your smart plug. The first video shows the entire pairing process, while the second video helps you set up a schedule with your smart plug (ie: if you want your plug to turn on and off at certain times). Thank you for your purchase and we hope you enjoy your product!

Vera Light Schedule Setup